Posted on: 20/11/2026
Role Overview:
This is a full-stack embedded role. You will work directly with the ASR/ML team on the audio pipeline, the software platform team on FHIR and HMIS adapters, QA on IEC 60601-1 and ISO 14971, and manufacturing on DFM, harness, and the calibration line.
What You'll Own:
You will own the embedded hardware and firmware end to end - from PCB design through field reliability.
1. PCB Design and Hardware Bring-up:
- Design PCBs from schematic capture through layout: carrier board, isolated patient-side island, biosignal front-end, and power subsystem boards, using KiCad or Altium.
- Select components from datasheets, maintain the BOM, and manage DFM reviews with manufacturing.
- Bring up SoC carrier boards: USB 3.2, MIPI CSI-2, M.2, HDMI, GPIO; validate with a logic analyser and oscilloscope.
- Design and verify the isolated patient-side island: 2xMOPP barrier, isolated DC-DC converters, digital isolators across UART bridges, creepage and clearance per IEC 60601-1.
- Implement ECG front-end (ADS1293): right-leg drive, common-mode rejection, and plate-contact detection.
- Design the power subsystem: 24 V medical PSU, LiFePO4 BMS, UPS switchover with zero-glitch handover.
2. Firmware and Embedded Software :
- Write and maintain JetPack Linux service containers: device-manager, ASR-bridge, vision, report-builder, FHIR-sync, admin-fleet.
- Implement UART/TTL drivers for medical grade sensors; output a unified sensor-reading struct; never alter numeric values after they leave the sensor.
- Implement Bluetooth LE drivers and manage BT LE radio scheduling to avoid audio dropouts.
- Write screen-read OCR fallback pipeline for sensor reading.
- Control ROBOTIS Dynamixel XL430 pan-tilt servos via U2D2/TTL bus: face-tracking loop at <= 20 Hz, soft stops, servo scheduling outside speech turns.
- Manage the USB device tree.
3. OTA, Security, and Fleet Management:
- Build and maintain a signed OTA pipeline: Ed25519 firmware signing, A/B partitioning, watchdog rollback, model hot-swap without reboot.
- Implement fleet telemetry: per-unit uptime, UART timeout counts, BT pairing failure counts, NVMe SMART health - store-and-forward over LTE.
- Keep the platform secure: encrypted patient records at rest, signed OTA, consent on every recording, DPDP Act 2023 compliance.
4. ISO/IEC Compliance and Test:
- Own the embedded contributions to IEC 60601-1 (electrical safety), IEC 60601-1-2 (EMC), IEC 62304 (software lifecycle), ISO 14971 (risk management), and ISO 13485 (QMS).
- Design and validate PCBs to pass medical-grade standards: patient leakage current, dielectric strength across the 2xMOPP barrier, ESD immunity, radiated and conducted emissions.
- Build calibration station fixtures and bench rigs; run EVT and DVT acceptance tests; contribute DHR and DMR entries in ERPNext.
- Coordinate pre-compliance EMC scans, formal IEC lab testing, and CDSCO/BIS filing support.
What You Bring:
- 3 - 5 years of hands-on embedded hardware and firmware experience, with at least some exposure to medical or regulated devices.
- PCB schematic capture and layout in KiCad or Altium: you have designed a multi-layer board that went into production, including component selection, DFM review, and BOM management.
- Experience testing and validating PCBs against industry or ISO-family standards - patient leakage, isolation barriers, EMC pre-compliance, or equivalent regulated-industry testing.
- Embedded Linux on ARM SoCs: systemd, containerisation (Docker), device tree, U-Boot or equivalent secure-boot chain.
- UART/TTL and Bluetooth LE peripheral drivers written from vendor protocol documents, not example code.
- USB device tree management: V4L2, ALSA, SANE, HID, or similar subsystems under Linux.
- Power electronics: DC-DC converters, BMS, UPS switchover logic, rail sequencing.
- Logic analyser and oscilloscope fluency: you debug UART framing, SPI timing, and power rail noise with instruments, not guesswork.
- Python or C++ to write firmware services, bench test scripts, and calibration tooling.
- Comfortable working alongside QA, regulatory affairs, and manufacturing teams - you read a risk file and contribute to it.
Good to Have:
- Formal IEC 60601-1 or IEC 60601-1-2 lab testing experience (submissions, non-conformance closure).
- ISO 13485 QMS contribution: DHR/DMR entries, supplier qualification, calibration SOPs.
- BT LE GATT profile implementation from scratch.
- OTA pipeline design: A/B partitioning, signed firmware, watchdog rollback.
- LTE modem bring-up under Linux.
- Experience with medical sensor OEM.
Did you find something suspicious?
Posted by
Posted in
Semiconductor/VLSI/EDA
Functional Area
Embedded / Kernel Development
Job Code
1685061