HamburgerMenu
hirist

Embedded HW/SW Engineer - Medical Devices

Neemtree
3 - 7 Years
Bangalore

Posted on: 20/11/2026

Job Description

Role Overview:

This is a full-stack embedded role. You will work directly with the ASR/ML team on the audio pipeline, the software platform team on FHIR and HMIS adapters, QA on IEC 60601-1 and ISO 14971, and manufacturing on DFM, harness, and the calibration line.

What You'll Own:

You will own the embedded hardware and firmware end to end - from PCB design through field reliability.

1. PCB Design and Hardware Bring-up:

- Design PCBs from schematic capture through layout: carrier board, isolated patient-side island, biosignal front-end, and power subsystem boards, using KiCad or Altium.

- Select components from datasheets, maintain the BOM, and manage DFM reviews with manufacturing.

- Bring up SoC carrier boards: USB 3.2, MIPI CSI-2, M.2, HDMI, GPIO; validate with a logic analyser and oscilloscope.

- Design and verify the isolated patient-side island: 2xMOPP barrier, isolated DC-DC converters, digital isolators across UART bridges, creepage and clearance per IEC 60601-1.

- Implement ECG front-end (ADS1293): right-leg drive, common-mode rejection, and plate-contact detection.

- Design the power subsystem: 24 V medical PSU, LiFePO4 BMS, UPS switchover with zero-glitch handover.

2. Firmware and Embedded Software :

- Write and maintain JetPack Linux service containers: device-manager, ASR-bridge, vision, report-builder, FHIR-sync, admin-fleet.

- Implement UART/TTL drivers for medical grade sensors; output a unified sensor-reading struct; never alter numeric values after they leave the sensor.

- Implement Bluetooth LE drivers and manage BT LE radio scheduling to avoid audio dropouts.

- Write screen-read OCR fallback pipeline for sensor reading.

- Control ROBOTIS Dynamixel XL430 pan-tilt servos via U2D2/TTL bus: face-tracking loop at <= 20 Hz, soft stops, servo scheduling outside speech turns.

- Manage the USB device tree.

3. OTA, Security, and Fleet Management:

- Build and maintain a signed OTA pipeline: Ed25519 firmware signing, A/B partitioning, watchdog rollback, model hot-swap without reboot.

- Implement fleet telemetry: per-unit uptime, UART timeout counts, BT pairing failure counts, NVMe SMART health - store-and-forward over LTE.

- Keep the platform secure: encrypted patient records at rest, signed OTA, consent on every recording, DPDP Act 2023 compliance.

4. ISO/IEC Compliance and Test:

- Own the embedded contributions to IEC 60601-1 (electrical safety), IEC 60601-1-2 (EMC), IEC 62304 (software lifecycle), ISO 14971 (risk management), and ISO 13485 (QMS).

- Design and validate PCBs to pass medical-grade standards: patient leakage current, dielectric strength across the 2xMOPP barrier, ESD immunity, radiated and conducted emissions.

- Build calibration station fixtures and bench rigs; run EVT and DVT acceptance tests; contribute DHR and DMR entries in ERPNext.

- Coordinate pre-compliance EMC scans, formal IEC lab testing, and CDSCO/BIS filing support.

What You Bring:

- 3 - 5 years of hands-on embedded hardware and firmware experience, with at least some exposure to medical or regulated devices.

- PCB schematic capture and layout in KiCad or Altium: you have designed a multi-layer board that went into production, including component selection, DFM review, and BOM management.

- Experience testing and validating PCBs against industry or ISO-family standards - patient leakage, isolation barriers, EMC pre-compliance, or equivalent regulated-industry testing.

- Embedded Linux on ARM SoCs: systemd, containerisation (Docker), device tree, U-Boot or equivalent secure-boot chain.

- UART/TTL and Bluetooth LE peripheral drivers written from vendor protocol documents, not example code.

- USB device tree management: V4L2, ALSA, SANE, HID, or similar subsystems under Linux.

- Power electronics: DC-DC converters, BMS, UPS switchover logic, rail sequencing.

- Logic analyser and oscilloscope fluency: you debug UART framing, SPI timing, and power rail noise with instruments, not guesswork.

- Python or C++ to write firmware services, bench test scripts, and calibration tooling.

- Comfortable working alongside QA, regulatory affairs, and manufacturing teams - you read a risk file and contribute to it.

Good to Have:

- Formal IEC 60601-1 or IEC 60601-1-2 lab testing experience (submissions, non-conformance closure).

- ISO 13485 QMS contribution: DHR/DMR entries, supplier qualification, calibration SOPs.

- BT LE GATT profile implementation from scratch.

- OTA pipeline design: A/B partitioning, signed firmware, watchdog rollback.

- LTE modem bring-up under Linux.

- Experience with medical sensor OEM.

info-icon

Did you find something suspicious?

Similar jobs that you might be interested in

Loading chat...